Pill Press

Pill Press

REFLEX Analytical's benchtop Pill Press provides a convenient and economical means for compressing powdered materials into pill form without incurring the cost normally associated with expensive pill making machinery. It is a compact, hand-operated press that can be used anywhere in the laboratory, requiring very little bench space and no fixed mounting. The Pill Press produces uniform pills in a polished die and ejects them smoothly into a receiver without incident of contamination.

The Pill Press is a stand alone accessory 10"H x 5"W x 9"D with a 7" lever arm, weighs 17 pounds and provides a 1.25" ram stroke. Available die sizes range from 2mm - 13mm (scroll below). Custom in between sizes are available upon request. Die sizes 4.5mm and smaller are made from 17-4PH Stainless Steel. Die sizes 1/4" and larger are made from T-303 Stainless Steel. Die components are heat treated for added strength and hardness. The depth of cavity is 1" for 3/8" and 1/2" dies, 0.75" for 3mm, 4.5mm, 1/8", and 1/4" dies. The press is supplied with a universal die holder which locates and aligns each die set. Choose one or more die sets depending upon the size(s) required for your application. Spare universal die holders are also available to increase productivity (as one pill is pressed, another can be prepared). Scroll below for order details.

The pills produced in the Pill Press are cylindrical in shape with flat ends. Their height or thickness depends upon the amount of material compressed and the force applied. The dies are not fastened down. They automatically align with the press ram and may be slipped out from under the ram for quick reloading.

The compressive force in this press is developed by hand pressure on a lever attached to a large steel cam. This press system is designed to provide a steadily increasing mechanical advantage up to a ratio of approximately 50 to 1 at the end of the stroke. Thus, a force of 20 pounds applied to the lever develops approximately 1000 pounds on the press ram which is adequate to produce firm pills from most powdered materials (usually without adding a binder).

The anvil which supports the die in the Pill Press is attached to a heavy screw post so that it can be raised or lowered. Rotating the anvil to raise or lower the die makes it possible to produce pills of any desired thickness using the maximum force of the press. When compressing light or fluffy materials the die can be raised after successive ram strokes to compensate for the reduction in the volume of the charge. The variable anvil setting can also be used as a means for adjusting the amount of pressure applied to a pellet. If duplicate pills of equal density are desired, these can be made by using equal amounts of sample and leaving the anvil at a fixed setting while taking the ram through its full stroke when forming each pill.

Pill samples are equally important in other investigative and test procedures. Laboratories engaged in pharmaceutical, biological, nutrition and spectrographic operations find frequent uses for pills and wafers of the types that can be made in the Pill Press. Spectroscopists find this device excellent for preparing small samples to be analyzed in an emission spectrometer.

CLICK HERE to preview other solid and semi-solid sampling accessories such as evacuable pellet dies and pellet molds, XRF dies, manual and auto lab presses, polymer film makers, and much more.

Send This Page to a Colleague
Lab Pellet Press
Lab Pellet Press

Lab Pellet Press with Universal Die Holder. Requires a Pellet Die Set (choose from standard sizes and optional in between sizes from 2 – 13mm)

Method: Solid Sampling

Technique: Compresses powdered materials into pellet form; circular in shape with flat ends.

Small Scale Laboratory Applications: Emission Spectroscopy, Calorimetry, Pharmaceutical, Nutraceutical, Biological, Nutritional Supplements, Vitamin Supplements and more.

Press Dimensions: 10"H x 5"W x 9"D with 7" lever arm

Press Weight: 17 lbs

Warranty: Guaranteed to be free from defects in material and workmanship for a period of 12 months from the date of shipment.

Pellet Press Instructions CLICK HERE
$1,795.00
2800
Standard Pellet Die Sets
Standard Pellet Die Sets

Pellet Die Sets for Press Part Number 2800

Standard Sizes: 1/8" 1/4" 3/8" 1/2"

Includes: Die Chamber and Die Plunger (as pictured)

Pellet Press and Die Specifications CLICK HERE
$695.00
280X
Size: 
Spare Universal Pellet Die Holder
Universal Pellet Die Holder for Press Part Number 2800

Accommodates Pellet Die Set Sizes: 2 - 13mm

Cross-Sectional Illustration CLICK HERE
$195.00
2810
Optional Pellet Die Sets
Optional Pellet Die Sets for Press Part Number 2800

Specify Diameter When Ordering

Optional Sizes: 2mm 2.25mm 2.50mm 2.75mm 3mm 3.25mm 3.50mm 3.75mm 4mm 4.25mm 4.50mm 4.75mm 5mm 5.25mm 5.50mm 5.75mm 6mm 6.25mm 6.50mm 6.75mm 7mm 7.25mm 7.50mm 7.75mm 8mm 8.25mm 8.50mm 8.75mm 9mm 9.25mm 9.50mm 9.75mm 10mm 10.25mm 10.50mm 10.75mm 11mm 11.25mm 11.50mm 11.75mm 12mm 12.25mm 12.50mm 12.75mm 13mm

Available Optional In Between Sizes: 2 - 13mm

Includes: Die Chamber and Die Plunger (as pictured)
$1,295.00
2810-XXX
Size: